Products
Support
Platinum Division to provide you with the best after sales service, have any questions and suggestions you can contact us.
Contact Phone
-
Tel:
(86)0755-26654881
-
Fax:
(86)0755-29574277
Alloy steel powder
-
Alloy steel powder Characteristic
1.Good sphericity, good flowability, loose apparent
density and tap density.
2.Low oxygen content, high purity, uniform comp-
osition, non-segregation.
3.(D50<20μm) Ultra-fine gas atomized alloy steel
powder (D50<20μm).
- Applications
- Core Loss Curves
- Temp.Curves
- Frequency Curves
- DC Bias
- Specification
Produced through high purity nitrogen atomization, alloysteel powder has the advantages of low oxygen content, high purity and good sphericity, so it is widely used in metal injection molding, thermal spraying, laser cladding,die steel and so on.
Stainless steel series:
|
Grade |
Main composition |
||||||||
|
C |
Cr |
Ni |
Mo |
Si |
Mn |
Cu |
Nb |
Fe |
|
|
SUS430 |
≤0.12 |
16-18 |
- |
- |
≤1.0 |
≤1.0 |
- |
Bal |
|
|
SUS304 |
≤0.08 |
18.20 |
8-11 |
- |
≤1.0 |
≤2.0 |
- |
Bal |
|
|
SUS316L |
≤0.03 |
16-18 |
10-14 |
2.0-3.0 |
≤1.0 |
≤2.0 |
- |
Bal |
|
|
SUS17-4PH |
≤0.07 |
15.5-17.5 |
3.0-5.0 |
- |
≤1.0 |
≤1.0 |
3.5-4.5 |
0.15-0.45 |
Bal |
|
HK30 |
0.4-0.5 |
23-27 |
19-22 |
≤0.5 |
≤1.5 |
≤1.5 |
- |
1.2-1.5 |
Bal |
Nickel based series:
|
Grade |
Main composition |
|||||||||
|
C |
Fe |
Cr |
Mo |
Nb |
Si |
Al |
Ti |
Co |
Ni |
|
|
In625 |
≤0.1 |
≤5.0 |
20-23 |
8-10 |
3.15-4.15 |
≤0.5 |
≤0.4 |
≤0.4 |
≤1.0 |
Bal |
|
In718 |
≤0.08 |
Bal |
17-21 |
2.8-3.3 |
4.75-5.50 |
≤0.35 |
0.2-0.8 |
0.65-1.15 |
0.15 |
50-55 |
|
In713C |
0.08-0.16 |
≤2.5 |
11.5-13.5 |
3.8-4.8 |
1.8-2.5 |
≤0.5 |
5.5-6.4 |
0.5-1.0 |
1.8-2.8 |
Bal |
Cobalt-based series:
|
Grade
|
Main composition |
|||||||
|
C |
Si |
Ni |
Cr |
Mo |
W |
Fe |
Co |
|
|
Co基A |
2.60 |
1.45 |
＜2.00 |
31.00 |
＜0.50 |
12.50 |
＜2.00 |
Bal |
|
Co基B |
1.10 |
1.30 |
＜2.50 |
29.00 |
＜0.80 |
5.20 |
＜1.50 |
Bal |
|
Co基C |
1.65 |
1.40 |
2.50 |
29.50 |
＜0.50 |
9.00 |
＜1.50 |
Bal |
Note: Above data is typical value or mean value for reference only, it doesn’t represent the actual value.
| Part Number | AL ±8% | Permeability | Before coating After coating | Sample request | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Outer dimension | Inner dimension | Height | Outer dimension | Inner dimension | Height | |||||
| (mm/inch) | (mm/inch) | (mm/inch) | (mm/inch) | (mm/inch) | (mm/inch) | |||||
| max | min | max | max | min | max | |||||